EIM Replacement System
We have developed a replacement UPGRADED panel set which converts your boat to reliable Carling Lighted Tip Toggle Switches.
Our kit includes a new 12 port fuse block that is pre-wired to the new panel of switches. You will have to disconnect the main power feed to your old EIM and transfer it to the new fuse block. Instructions are included
Please email if you would like to see a copy of the installation instructions
You basically disconnect the main 24 pin harness plug from your EIM and connect it directly to our matching harness plug that is fed from the new switches. Electrical knowledge is required to insure a successful conversion.
It will be necessary to cut some fiberglass for clearance and secure harness wires.
This kit will retrofit The smaller Sundecks and Sport Boats that had peanut shaped pads for the switches and ignition and DID NOT HAVE peanut shaped recesses directly in the dashboard. The 200-220 Sundecks, 215, 225, 245 Weekender, and 2003-2004 240-260 Sundancer. with the Peanut Pad/EIM system. 1718632 1718631 1123785 1142314 1204619 1123793 1133800 1204619 1204353
This particular system WILL NOT WORK for the 240-270 Sundeck/240-260 Sundancer. The wiring is different and this kit does not have all of the accessories that the larger boats have. The proper kit for the 240-270 Sundeck/240-260 Sundancer and 245 Weekender includes a new premium switch panel and gauge panel ($400 value) so the pricing for the actual electrical part of the kit is almost the same
We also have complete replacement systems for the 200-220 Sundecks, 240-270 Sundecks, 240-260 Sundancer AND a complete replacement "Dual Kidney" and "Dual Eyebrow systems for the
We have had tremendous feedback:
"Techs usually come in my office to complain about stuff, not to
tell me how well thought out and properly executed someone’s product is. Caught
me off-guard. Thanks for that".
Tidewater Yacht Service, Baltimore
"I just wanted to let you know that the install went well. I
now have working switches again. The install instructions were straight
forward. I had to remove about a 2”x2” from the fiberglass to make the switches
on the right side fit. I also used my previous ignition.
Thank you for all of your help."
290 Sundancer -(Customer installation) -
you for all your help, my brother and I finally figured out the problem.
Everything is working and I am so relieved I can enjoy my boat again. The
replacement product is very well designed, thanks again.
I called FP Marine Monday morning and asked questions about
your EIM replacement for my 2003 SeaRay 200BR you gave me all info so I ordered
your system and received it Wed. It looked very professional and included all
hardware and directions. It was about 2hrs to install and worked perfect. I
would recommend your system to any sea ray owner to replace a very bad EMI
system, sea ray should have installed your system to start with. Thanks FP
Hi Ed , this has been the best replacement I have ever did
on anything! Everything was just plug and play! The only modification I needed
to do is cut bigger hole in the side cavity to push harness through. The new
replacement looks much better then original! Thank you for building this with
such a quality!
Thank you again! Dmitri
Everything went well with the install, I believe the
customer will be very happy. If you have any further questions please feel free
to give me a call at 770-720-2922. Thanks
Recently I purchased and installed myself, the EIM
replacement system for my 2007 Sea Ray 320 Sundancer. I am very pleased with
the quality and looks of the new toggle/rocker switches; what a big improvement
over the original switches. Initially when I saw the new replacement wiring
harness, it looked very complicated but actually turned out to be fairly simple
to install. Everything matched up perfectly, adjustments had to be made to the
dash to make the new switches fit but the templates made that easy. I would
highly recommend this product to anyone who is having trouble with their
switches like I did. Now everything works like it is supposed to and they look
great. Everyone that I spoke to at FP Marine were very helpful with the
questions I had. Thank you so much for developing this product and making my
boating more enjoyable.
Thanks again, Marty
I have attached several photos of the completed project. The sun
didn't cooperate and I will try to get better shots next week.
Note that the dash is not perfectly flat at these locations so I didn't crank
down on the bottom screws. The plates flex slightly in this installation.
It is a very straight forward installation but takes a little effort due to
access and cutting the holes. You remove the access panel in the storage
area behind the dash to get access to the wiring. Cutting the holes
would probably be best done with a Dremel tool and blade for fiberglass. I used
several different tools. The actual wire harness connections are straight
forward and very easy to complete. It does take a few hours due to the required
Looks fantastic when complete and works great! Love the back light on the
symbols. I didn't expect that.
On another issue, do you make replacement dash panels for the 220SD. I
could send you my old dash panel as a template. I would need a slight
modification in the standard hole templates since I use 3 large gauges
(standard is 2) and 1 fewer small gauge.
WE have modified the size of the
panels since this feedback.
also visit, join, and search www.clubsearay.com for more EIM
testimonials, step by step installation ideas and thousands of other Sea
Ray owners sharing information!!